Networks (GCSE & IGCSE Computer Science): Revision Notes and Worksheets
GCSE and IGCSE Computer Science networks: LANs and WANs, performance, client-server, hardware, star and mesh, Wi-Fi, IP and MAC addresses, protocols, layers.

Every message, web page and email you send crosses at least one network, and usually many. This guide covers GCSE and IGCSE networks: LANs and WANs, what affects network performance, client-server and peer-to-peer, network hardware, star and mesh topologies, wired and wireless connections, IP and MAC addresses, protocols and layers. Each part has a worked example and a worksheet for your exam board.
Cambridge IGCSE 0478 students: you only need E4, E7 and E9, and only the points marked IGCSE or Both boards. Parts E1, E2, E3, E5, E6, E10 and E11 are on the OCR J277 specification only. There is no part E8.
What does networks cover for OCR and Cambridge?
A network is two or more computers connected so they can share data and resources. OCR J277 has a whole topic on networks (1.3.1 and 1.3.2). Cambridge IGCSE 0478 asks for less: the NIC, MAC and IP addresses and the router (3.4), and the protocols HTTP and HTTPS (5.1.3). The table below is based on the OCR J277 specification (version 3.1) and the Cambridge IGCSE 0478 syllabus for 2026-2028, as checked in November 2026. GCSE only: the rest of OCR 1.3.1 (the internet as a network of networks, DNS and hosting) is covered in Module F, The internet; the Cloud is in Module B (B6).
Part | Topic | OCR J277 | Cambridge 0478 |
|---|---|---|---|
E1 | LANs and WANs (GCSE only) | 1.3.1 | not on syllabus |
E2 | Network performance (GCSE only) | 1.3.1 | not on syllabus |
E3 | Client-server and peer-to-peer (GCSE only) | 1.3.1 | not on syllabus |
E4 | Network hardware (both boards) | 1.3.1 | 3.4.1, 3.4.4 (NIC and router only) |
E5 | Star and mesh topologies (GCSE only) | 1.3.1 | not on syllabus |
E6 | Wired and wireless (GCSE only) | 1.3.2 | not on syllabus |
E7 | IP and MAC addresses (both boards) | 1.3.2 | 3.4.2, 3.4.3 |
E9 | Protocols and standards (both boards) | 1.3.2 | 5.1.3 (HTTP and HTTPS only) |
E10 | Email protocols (GCSE only) | 1.3.2 | not on syllabus |
E11 | Layers (GCSE only) | 1.3.2 | not on syllabus |
E1: What is the difference between a LAN and a WAN?
GCSE only. A LAN (local area network) covers a small geographical area, such as a home, a school or one office site. The hardware and cables in a LAN are usually owned and managed by the organisation that uses it.
A WAN (wide area network) covers a large geographical area, connecting LANs across cities or countries. The links in a WAN are usually leased from third parties, such as telecoms companies, and can be cables, phone lines or satellite links. The internet is the largest WAN. Another example is a bank that links the LANs in all its branches.
Worked example: LAN or WAN? (GCSE only)
Step 1: a hospital has 600 computers, all in buildings on one site, on cables it owns. The area is small and the hardware is its own: a LAN.
Step 2: a supermarket chain links the tills in 40 towns to its head office over lines rented from a telecoms company. The area is large and the links are leased: a WAN.
Step 3: the number of devices does not decide it. The size of the area and who owns the links do.
Practise E1: OCR questions · OCR mark scheme
E2: What affects the performance of a network?
GCSE only. Bandwidth is the amount of data that can be transferred in a given time, measured in units such as Mbps (megabits per second). More bandwidth means better performance. Other factors:
Number of devices connected: more devices share the bandwidth and create more traffic, so each one gets less and the network slows down.
Transmission media: wired connections are usually faster and more reliable than wireless; fibre optic cable has the highest bandwidth.
Wireless signal: it weakens with distance and with obstacles such as walls, and other devices and networks cause interference.
Amount and type of traffic: streaming video, large downloads and backups use a lot of bandwidth.
Hardware: a busy or low-specification server or switch can become a bottleneck.
Worked example: sharing the bandwidth (GCSE only)
An office has a 100 Mbps connection, shared equally between the devices using it at the same time.
Step 1: 4 devices are using it: 100 ÷ 4 = 25 Mbps each.
Step 2: a 5th device joins: 100 ÷ 5 = 20 Mbps each.
Step 3: explain it in exam words: more devices share the same bandwidth, so each device gets less bandwidth, and data takes longer to transfer.
Practise E2: OCR questions · OCR mark scheme
E3: What is the difference between client-server and peer-to-peer networks?
GCSE only. In a client-server network, a central server provides services, and clients request and use those services. For example, a web server provides web pages and a file server stores files and sends them back when asked. The server makes it easy to back up files centrally, manage security and user accounts, and install updates, and users can reach their files from any client. But servers are expensive, need specialist staff, and if the server fails, the clients lose access to its services.
In a peer-to-peer (P2P) network there is no central server. All computers have equal status and each acts as both client and server, sharing files and resources directly. It is cheap and easy to set up, and there is no single server to fail. But there is no central backup or security, files are spread across many machines, and a computer can slow down while others use its files.
Worked example: which network? (GCSE only)
Step 1: three people in a small design studio want to share a printer and some files, with little money and no technician. Peer-to-peer: cheap, easy to set up, no server to buy or manage.
Step 2: a company with 300 staff needs every file backed up each night and a login for each user. Client-server: central backups, security and user accounts.
Step 3: always give the reason from the scenario, not just the name of the network.
Practise E3: OCR questions · OCR mark scheme
E4: What hardware is needed to build a network?
Both boards. A computer needs a NIC (network interface card or controller) to access a network. A NIC can be wired (with an Ethernet port) or wireless (using radio waves). A router sends data to a specific destination on a network, using IP addresses, and connects networks together, for example connecting a local network to the internet.
IGCSE only: Cambridge 0478 names only the NIC and the router here. A NIC is given a MAC address at the point of manufacture (more in E7), and a router can assign IP addresses to the devices on its network.
GCSE only: OCR J277 also asks for the task of each piece of hardware needed to connect stand-alone computers into a LAN:
Switch: connects devices within a LAN, and uses MAC addresses to send data only to the device it is meant for.
Wireless access point (WAP): lets wireless devices connect to a wired network using radio waves.
Transmission media: what carries the data: copper (Ethernet) cable, fibre optic cable or radio waves.
A home "router" is usually several of these in one box: a router, a switch and a wireless access point.

Worked example: follow the data out of the building (both boards)
A desktop computer in an office sends a request to a website.
Step 1 (both boards): the computer's NIC puts the data onto the network.
Step 2 (GCSE only): the data travels down a copper cable to the switch, which sends it only to the router, using the router's MAC address.
Step 3 (both boards): the router sends the data to its destination on the internet, using the destination IP address.
Practise E4: OCR questions · OCR mark scheme · Cambridge questions · Cambridge mark scheme
E5: What are star and mesh topologies?
GCSE only. A topology is the way the devices on a network are connected.
In a star topology, every device connects to a central switch. If one device or cable fails, the others are not affected, it is easy to add devices, and the switch sends data only to the device it is meant for. But if the central switch fails, the whole network fails, and every device needs its own cable, which costs money.
In a mesh topology, devices connect directly to each other. In a full mesh, every device is linked to every other device. There are many routes for data, so there is no single point of failure: if one link fails, data is rerouted. But a wired mesh needs lots of cabling, so it is expensive and complex to set up and maintain. A wireless mesh avoids most of the cabling and extends coverage.

Worked example: counting the cables in a full mesh (GCSE only)
In a full mesh, each of the n devices links to the other n - 1 devices, and each cable is shared by two devices, so the number of cables is n(n - 1) ÷ 2.
Step 1: 5 devices: 5 × 4 ÷ 2 = 10 cables.
Step 2: 6 devices: 6 × 5 ÷ 2 = 15 cables. Adding one device added 5 cables.
Step 3: a star with 6 devices needs only 6 cables, one from each device to the switch. That is why a wired mesh is expensive.
Practise E5: OCR questions · OCR mark scheme
E6: What are the benefits of wired and wireless connections?
GCSE only. In a wired connection (Ethernet), devices connect to the network by cables, copper or fibre optic. Wired connections are usually faster, more reliable and harder to intercept. But cables cost money to buy and install, and devices cannot move around freely.
In a wireless connection (Wi-Fi), devices connect by radio waves through a wireless access point. Wi-Fi gives mobility, needs no cables and makes it easy to add devices. But it is usually slower, suffers from interference, and its range is limited, especially by walls. Anyone in range can pick up the signal, so the data should be encrypted.
Bluetooth is a short-range wireless connection between two devices close together, such as headphones and a phone. It uses little power and is easy to pair, but its range is short (about 10 metres) and its bandwidth is low. You do not need to know how the Ethernet, Wi-Fi or Bluetooth protocols work.
Worked example: recommend a connection (GCSE only)
A video editing company has desktop computers that stay on desks and move huge video files, and visitors who bring laptops to meetings.
Step 1: the desktops do not move and need a fast, reliable connection for large files: recommend wired (Ethernet).
Step 2: visitors need to move around and connect quickly without cables: recommend Wi-Fi, with the data encrypted.
Step 3: "recommend one or more" means you can choose both, as long as each choice is justified from the scenario.
Practise E6: OCR questions · OCR mark scheme
E7: What are IP addresses and MAC addresses?
Both boards. An IP address identifies a device on a network or the internet, so that data can be sent to the right destination. There are two versions:
IPv4: 32 bits, written as 4 denary numbers from 0 to 255, separated by full stops, for example 192.0.2.45.
IPv6: 128 bits, written as 8 groups of 4 hexadecimal digits, separated by colons, for example 2001:0db8:0000:0000:0000:0000:0000:0001. IPv6 was introduced because the 4.3 billion or so IPv4 addresses are running out; IPv6 gives vastly more.
A MAC (media access control) address is a unique address assigned to a device's NIC. It identifies the device on a local network. It is 48 bits, usually written as 12 hexadecimal digits in 6 pairs, separated by colons or hyphens, for example 6E-14-AB-90-2C-F7. In short: the MAC address gets data to the right device within a network; the IP address routes data between networks.
IGCSE only: a MAC address is given to the NIC at the point of manufacture and does not normally change. Its structure is a manufacturer code (the first half) followed by a serial code (the second half). An IP address is allocated by the network and can be static (it stays the same, which suits a server that must always be found at the same address) or dynamic (it is assigned when the device connects and can change, so addresses can be reused). OCR J277 lists static and dynamic IP addresses as not required.
Worked example: is this a valid IPv4 address? (both boards)
All the addresses here are from ranges set aside for examples and private networks.
Step 1: 192.0.2.45: four numbers, separated by full stops, each from 0 to 255. Valid.
Step 2: 192.0.2.256: four numbers, but 256 is bigger than 255. Each number is stored in 8 bits, and the largest 8-bit value is 255. Not valid.
Step 3: 6E-14-AB-90-2C-F7 is not an IP address at all: 6 pairs of hexadecimal digits make it a MAC address. (IGCSE only: 6E-14-AB is the manufacturer code and 90-2C-F7 is the serial code.)
Practise E7: OCR questions · OCR mark scheme · Cambridge questions · Cambridge mark scheme
E9: What are protocols and standards?
Both boards. A protocol is a set of rules for transferring data between devices.
HTTP (hypertext transfer protocol): the rules a web browser uses to request web pages from a web server. The browser sends a request for a page, and the web server responds by sending the page's HTML and files. HTTP sends data as plain text, so if it is intercepted it can be understood.
HTTPS (hypertext transfer protocol secure): the same purpose as HTTP, but the data between the browser and the server is encrypted (using SSL/TLS). It is used for logins and payments, and the address starts https://, often with a padlock in the address bar.
IGCSE only: Cambridge 0478 needs only HTTP and HTTPS: their purpose and how they operate.
GCSE only: OCR J277 also asks for these:
Standard: a set of rules for an area of computing, so that hardware and software from different manufacturers can work together. You do not need to know individual standards.
Different protocols are used for different purposes; know the purpose and key features of each.
TCP/IP (transmission control protocol / internet protocol): TCP splits data into packets, puts them back in order and checks them; IP addresses and routes the packets.
FTP (file transfer protocol): transfers files across a network, for example uploading a website's files to a web server.
Worked example: match the protocol to the job (both boards)
Step 1 (both boards): a library website shows its opening times: HTTP. It is a request for a web page, and nothing secret is sent.
Step 2 (both boards): a user logs in to their library account: HTTPS, because the password is sent and must be encrypted.
Step 3 (GCSE only): a web designer uploads 200 new page files to the library's web server: FTP, because it transfers files.
Practise E9: OCR questions · OCR mark scheme · Cambridge questions · Cambridge mark scheme
E10: How do the email protocols POP, IMAP and SMTP work?
GCSE only. Sending and receiving email use different protocols.
SMTP (simple mail transfer protocol): sends email from a client to a mail server, and between mail servers.
POP (post office protocol): downloads email from the mail server to one device, and usually deletes the copy on the server. The email is then stored only on that device, so it can be read offline but is not synced with other devices.
IMAP (internet message access protocol): the email stays on the mail server, and each device views and syncs a copy. Emails read, deleted or moved to a folder show the same on every device, but IMAP needs storage on the server and a connection to it.
Worked example: POP or IMAP? (GCSE only)
Step 1: a plumber reads email on a phone in the van, a tablet at home and a laptop in the office. They want to see the same inbox everywhere: IMAP, because the email stays on the server and syncs.
Step 2: a writer uses one computer only and wants their email stored on it to read offline: POP.
Step 3: whichever is chosen for receiving, sending the replies uses SMTP.
Practise E10: OCR questions · OCR mark scheme
E11: What are layers and why are they used?
GCSE only. Network communication is split into layers. Each layer does one job and has its own protocols. Each layer uses the layer below it and serves the layer above: data is passed down the layers to be sent and up the layers when it is received. OCR's teaching example is the 4-layer TCP/IP model, but you do not need the names or functions of its layers.
The benefits of layers:
They break a complex task into manageable parts (decomposition), and each layer can be developed separately.
One layer can be changed or updated without affecting the other layers.
Layers follow standards, so hardware and software from different manufacturers can work together.
Problems are easier to find and fix, because they can be traced to one layer.
Worked example: "Explain one benefit of using layers" (GCSE only)
Step 1: state the benefit: one layer can be changed without affecting the others.
Step 2: expand it with an example: a laptop swaps a wired connection for Wi-Fi. Only the layer that deals with the connection changes; the web browser and HTTP work exactly as before.
Step 3: an "explain" question wants the point and the reason or example. That is two marks.
Practise E11: OCR questions · OCR mark scheme
Common exam mistakes in networks
(GCSE) LAN and WAN: deciding by the number of computers. It is the size of the geographical area, and whether the links are owned or leased.
(GCSE) Performance: writing "more devices make it slower" without saying why: they share the bandwidth.
(GCSE) Mixing up the switch (sends data to the right device within a LAN, using MAC addresses) and the router (sends data between networks, using IP addresses).
(GCSE) Star topology: saying one cable failing stops the network. Only the central switch failing does that.
Writing an IPv4 address with a number above 255, or saying IPv4 is 4 bytes of hexadecimal. It is denary; IPv6 and MAC addresses are hexadecimal.
HTTPS: writing that it stops data being intercepted. It encrypts the data, so intercepted data cannot be understood.
(GCSE) Email: saying POP or IMAP sends email. Sending is SMTP.
Quick recap
E1: (GCSE only) a LAN covers a small area on hardware the organisation owns; a WAN covers a large area on leased links; the internet is the largest WAN.
E2: (GCSE only) performance depends on bandwidth, the number of devices sharing it, the transmission media, the wireless signal, the traffic and the hardware.
E3: (GCSE only) client-server: a central server provides services to clients; peer-to-peer: no server, all computers equal.
E4: NIC to access a network; router sends data to its destination and connects a LAN to the internet; switch, WAP and media GCSE only; router assigns IP addresses IGCSE only.
E5: (GCSE only) star: central switch, a single point of failure; mesh: many routes, lots of cabling; full mesh cables = n(n - 1) ÷ 2.
E6: (GCSE only) Ethernet is fast and reliable; Wi-Fi gives mobility; Bluetooth is short range and low power.
E7: IPv4 is 32 bits, 4 denary numbers 0-255; IPv6 is 128 bits of hexadecimal; MAC is 48 bits, 12 hex digits on the NIC; MAC structure and static or dynamic IP IGCSE only.
E9: a protocol is a set of rules; HTTP requests web pages, HTTPS encrypts them; standards, TCP/IP and FTP GCSE only.
E10: (GCSE only) SMTP sends; POP downloads to one device; IMAP keeps email on the server and syncs.
E11: (GCSE only) layers split communication into parts with their own protocols, so each can be changed separately.
Download the whole module
Frequently asked questions
Which parts of networks are on the Cambridge IGCSE 0478 syllabus?
Only E4, E7 and E9: the NIC and the router, IP and MAC addresses, and the protocols HTTP and HTTPS. LANs and WANs, network performance, client-server and peer-to-peer, topologies, wired and wireless, email protocols and layers are on OCR J277 only.
What is the difference between a switch and a router?
A switch connects devices within a LAN and uses MAC addresses to send data only to the device it is meant for. A router sends data between networks using IP addresses, for example connecting a local network to the internet.
What are the advantages and disadvantages of a star topology?
If one device or cable fails, the rest of the network is not affected, and it is easy to add devices. But if the central switch fails the whole network fails, and every device needs its own cable.
What is the difference between an IP address and a MAC address?
An IP address identifies a device on a network or the internet so that data can be routed to it; IPv4 uses 4 denary numbers from 0 to 255. A MAC address is a unique 48-bit address given to a device's network interface card, written as 12 hexadecimal digits, and it identifies the device within a local network.
What is the difference between HTTP and HTTPS?
Both are the rules a web browser uses to request web pages from a web server. HTTPS also encrypts the data sent between the browser and the server, so if it is intercepted it cannot be understood.
What is the difference between POP and IMAP?
POP downloads email from the mail server to one device and usually deletes it from the server. IMAP keeps the email on the server, so every device sees the same, synced inbox.
Previous module: Data transmission revision notes.
More help: browse the GCSE Computer Science revision hub.