Data Transmission (GCSE & IGCSE Computer Science): Revision Notes and Worksheets
GCSE and IGCSE Computer Science data transmission: packets, serial and parallel, USB, parity, checksums, echo checks, check digits, ARQ and encryption.

A photo sent to a friend on the other side of the world does not travel in one piece, and it can be damaged or copied on the way. This guide covers GCSE and IGCSE data transmission: packets and packet switching, serial and parallel, simplex and duplex, USB, parity checks and checksums, echo checks, check digits, ARQ and encryption. Each part has a worked example and a worksheet for your exam board.
OCR J277 students: you only need D6 (encryption). Parts D1 to D5 are on the Cambridge IGCSE 0478 syllabus only. The OCR J277 specification (version 3.1) lists packet switching as removed content, so skip straight to D6.
What does data transmission cover for OCR and Cambridge?
Data transmission is about how data is sent from one device to another: how it is split up and routed, how the bits travel down a wire, how errors are spotted, and how the data is kept secure. Cambridge IGCSE 0478 has a whole topic on it (2.1 to 2.3). OCR J277 only asks for the principle of encryption, in three places in its specification. The table below is based on the OCR J277 specification (version 3.1) and the Cambridge IGCSE 0478 syllabus for 2026-2028, as checked in November 2026.
Part | Topic | OCR J277 | Cambridge 0478 |
|---|---|---|---|
D1 | Packets and packet switching (IGCSE only) | not on spec | 2.1.1 |
D2 | Serial, parallel, simplex and duplex (IGCSE only) | not on spec | 2.1.2 |
D3 | The USB interface (IGCSE only) | not on spec | 2.1.3 |
D4 | Parity checks and checksums (IGCSE only) | not on spec | 2.2.1, 2.2.2 |
D5 | Echo checks, check digits and ARQ (IGCSE only) | not on spec | 2.2.2, 2.2.3, 2.2.4 |
D6 | Encryption (symmetric and asymmetric IGCSE only) | 1.3.2, 1.4.2, 1.5.2 (principle only) | 2.3.1, 2.3.2 |
D1: What are packets and how does packet switching work?
IGCSE only. When data is sent across a network it is not sent as one big block. It is broken down into packets, and each packet is sent on its own. Every packet has three parts:
Packet header: the destination address (where it is going), the packet number (its place in the order) and the originator's address (where it came from).
Payload: the actual data, this packet's piece of the file.
Trailer: marks the end of the packet, and can hold error checking data.
In packet switching, each packet could take a different route across a network of routers. A router reads the packet's destination address and controls the route it takes. Some routes are slower than others, so packets may arrive out of order. Once the last packet has arrived, the packets are reordered using the packet numbers in their headers.

Worked example: reading a packet header (IGCSE only)
A packet arrives with this header: destination address 203.0.113.52, packet number 3, originator's address 192.0.2.15. Five packets were sent, and they arrive in the order 2, 5, 1, 3, 4.
Step 1: the router uses the destination address, 203.0.113.52, to decide where to send the packet next.
Step 2: the packet number, 3, says this payload is the third piece of the file. The originator's address says who sent it.
Step 3: packet 4 is the last to arrive, so the file can only be rebuilt after it arrives. The packets are then put back in the order 1, 2, 3, 4, 5 using their packet numbers.
Practise D1: Cambridge questions · Cambridge mark scheme
D2: What are serial, parallel, simplex and duplex transmission?
IGCSE only. For any connection, ask two questions: how many bits are sent at once, and which way can the data go?
Serial transmission sends data one bit at a time down a single wire. The bits arrive in order, so they cannot be skewed, and one wire means less interference, so serial is reliable over long distances. Its drawback is that it is slower than parallel. Parallel transmission sends several bits at the same time down several wires. It is faster over short distances, but over long distances the bits can arrive at different times, out of order (the data is skewed), and the wires cause more interference.
Simplex sends data in one direction only, like a radio station to a radio. Half-duplex sends data in both directions, but only one direction at a time, like a two-way radio. Full-duplex sends data in both directions at the same time, like a video call.
Worked example: choosing a method (IGCSE only)
Two offices 40 km apart send data to each other at the same time.
Step 1: how many bits at once? 40 km is a long way, so parallel bits could be skewed: choose serial.
Step 2: which way? Both ways at the same time: choose full-duplex.
Step 3: answer serial full-duplex, and justify each word: no skew over a long distance, and data in both directions at once.
Practise D2: Cambridge questions · Cambridge mark scheme
D3: What is USB and how does it transmit data?
IGCSE only. USB stands for universal serial bus. It is a standard interface for connecting devices such as keyboards, printers, phones and memory sticks to a computer. It is serial: data is sent one bit at a time down a single wire. The cable carries power as well as data, so a device can be powered or charged by the computer. When a device is plugged in, it is detected automatically and the right driver is installed automatically.
Benefits: a universal connection used by many devices; the cable cannot be inserted incorrectly; it supports different transmission speeds; newer versions are backward compatible; devices can be powered through the cable and are detected automatically. Drawbacks: slower transmission than a parallel connection, and the cable can get in the way or limit where the device can go.
Worked example: "Explain how data is sent using USB" (IGCSE only)
Step 1: ask what the S stands for: serial.
Step 2: say what serial means in two points: data is sent one bit at a time, down a single wire. That is two marks.
Step 3: do not write just "fast": Cambridge credits "fast transmission speed", not "fast" on its own.
Practise D3: Cambridge questions · Cambridge mark scheme
D4: How do parity checks and checksums detect errors?
IGCSE only. Interference during transmission can cause errors: data can be lost, extra data can be gained, or data can be changed (a 0 becomes a 1). So the receiver needs a way to check the data.
In a parity check, the sender and receiver first agree on odd or even parity. A parity bit is added to each byte (here the leftmost bit) to make the number of 1s even (even parity) or odd (odd parity). After transmission, the receiver counts the 1s in each byte. If the count does not match the agreed parity, an error is detected and the data is sent again. A parity check cannot tell you which bit changed, and if two bits change the parity is still right, so the error is missed.
A parity block check sends a block of bytes, each with its own parity bit, then adds a parity byte at the end: each of its bits is the parity bit for one column. If one bit changes, the receiver finds the byte (row) and the column with the wrong parity: the bit where they cross is the error, and it can be corrected.
A checksum is a value calculated from the data using an agreed algorithm and sent with it. The receiver recalculates the checksum from the data it receives. If the two values do not match, an error is detected and the data is sent again.

Worked example: an even parity bit, and a parity block (IGCSE only)
Step 1: the data is 1010011. Count the 1s: there are 4. 4 is already even, so the even parity bit is 0 and the byte is 01010011.
Step 2: a block of four bytes, all with even parity, is sent: 01010011, 11110101, 00101110, 11000110. Count the 1s in each column: 2, 3, 2, 2, 1, 3, 3, 2. Each odd column gets a 1, so the parity byte is 01001110.
Step 3: byte 3 arrives as 00101010. It has 3 ones (odd), so byte 3 is wrong. Column 6 (from the left) now has an odd number of 1s too.
Step 4: the error is the bit where byte 3 and column 6 cross. Flip it back to 1 and byte 3 is 00101110 again.
Step 5 (checksum): with the simple algorithm "add the bytes", the sender's checksum is 83 + 245 + 46 + 198 = 572. The receiver gets 83 + 245 + 42 + 198 = 568, which does not match, so an error is detected.
Practise D4: Cambridge questions · Cambridge mark scheme
D5: What are echo checks, check digits and ARQ?
IGCSE only. In an echo check, the receiver sends a copy of the data back to the sender, and the sender compares the copy with the original. If they are different, an error has occurred and the data is sent again. Its drawbacks: the sender cannot tell whether the error happened on the way there or on the way back, and all the data is sent twice.
A check digit checks data entry, when a number is typed in or scanned. It is calculated from the other digits and added to the end of the number, for example on bar codes and ISBNs (the numbers that identify books). When the number is entered, the check digit is calculated again; if it does not match, the number was entered wrongly. It catches errors such as an incorrect digit or two digits swapped.
Automatic repeat query (ARQ) uses acknowledgements and a timeout. The sender starts a timer when it sends the data. The receiver checks the data for errors (for example with a parity check). No error: it sends a positive acknowledgement. Error: it sends a negative acknowledgement, and the data is sent again. If no acknowledgement arrives before the timeout, the data is sent again, and this repeats until an acknowledgement is received.
Worked example: a check digit by modulo 11 (IGCSE only)
The syllabus asks you to describe how a check digit is used, not to learn one method. If a question asks for a calculation, it gives the method. Here is one method, in full: multiply the first four digits by the weights 5, 4, 3 and 2, add the results, and the check digit is the number you must add to that total to reach the next multiple of 11.
Step 1: the code starts 3, 1, 7, 4. Multiply by the weights: 3 x 5 = 15, 1 x 4 = 4, 7 x 3 = 21, 4 x 2 = 8.
Step 2: add them: 15 + 4 + 21 + 8 = 48.
Step 3: the next multiple of 11 is 55, and 55 - 48 = 7. The check digit is 7, so the full code is 31747.
Step 4: someone types 31847. Recalculate: 15 + 4 + 24 + 8 = 51, which needs 4 to reach 55. 4 is not 7, so an error is detected.
Practise D5: Cambridge questions · Cambridge mark scheme
D6: What is encryption and why is it used?
Both boards. When data is sent across a network it can be intercepted: someone can get a copy as it travels. Encryption uses an algorithm and a key to scramble the data so that, if it is intercepted, it cannot be understood without the key. Only someone with the right key can decrypt it, turning it back into the original data. Encryption does not stop the data being intercepted or stolen; it makes intercepted data meaningless. It is used to secure data sent across network connections, such as secure websites (HTTPS), Wi-Fi and online payments.
GCSE only: OCR J277 asks for the principle of encryption in three places: securing data sent across network connections (1.3.2), encryption as a prevention method against data interception and theft (1.4.2), and encryption software as a utility (1.5.2). You do not need symmetric or asymmetric encryption, and you do not need the words plaintext and ciphertext. Say that encrypted data cannot be understood without the key, rather than "cannot be read".
IGCSE only: Cambridge 0478 uses the terms plaintext (the original data) and ciphertext (the encrypted data), and asks for two types. Symmetric encryption uses the same key to encrypt and decrypt, so the key has to be sent to the receiver, and if it is intercepted the data can be decrypted. Asymmetric encryption uses a matching pair: a public key, shared openly, encrypts the data, and only the matching private key, kept secret by the receiver and never sent, can decrypt it.

Worked example: "My data is encrypted, so nobody can intercept it"
Step 1: ask what encryption actually changes: not whether the data can be taken, but what the taker gets.
Step 2: the data can still be intercepted, but it is scrambled, so it cannot be understood without the key. The claim is wrong.
Step 3 (IGCSE only): Kai sends Ava a file with asymmetric encryption. He encrypts it with Ava's public key, so only Ava's private key can decrypt it.
Practise D6: OCR questions · OCR mark scheme · Cambridge questions · Cambridge mark scheme
Common exam mistakes in data transmission
(IGCSE) Packets: calling the payload the header, or forgetting that packets are reordered once the last packet arrives, using the packet numbers.
(IGCSE) Serial: saying serial data can be skewed (skew is a parallel problem), or saying packets go down the wire one at a time (it is bits).
(IGCSE) USB: writing "fast" on its own, or "can be used over long distances".
(IGCSE) Parity: not saying who counts what: the receiver counts the 1s in each byte.
(IGCSE) Mixing up a check digit (checks data entry) with a checksum (checks data after transmission).
(IGCSE) ARQ: adding negative acknowledgements when the question's system uses positive acknowledgements only.
Encryption: writing that encryption stops data being intercepted or stolen. It can still be intercepted; it just cannot be understood without the key.
Quick recap
D1: (IGCSE only) data is broken into packets: header (destination address, packet number, originator's address), payload, trailer; routers route each packet; reordered at the end.
D2: (IGCSE only) serial: one bit at a time, reliable over long distances; parallel: several bits at once, faster over short distances but can skew; simplex, half-duplex, full-duplex.
D3: (IGCSE only) USB is a universal serial bus: serial, carries power, detected automatically with drivers installed.
D4: (IGCSE only) parity bit makes the number of 1s odd or even; a parity block finds the exact bit; a checksum is recalculated by the receiver.
D5: (IGCSE only) echo check sends a copy back; a check digit checks data entry (ISBNs, bar codes); ARQ uses acknowledgements and a timeout.
D6: encryption scrambles data with an algorithm and a key so it cannot be understood without the key; symmetric (one key) and asymmetric (public and private keys) IGCSE only.
Download the whole module
Frequently asked questions
Is packet switching on the OCR GCSE Computer Science specification?
No. OCR J277 (version 3.1) lists packet switching as removed content, so parts D1 to D5 of this module are for Cambridge IGCSE 0478 only. OCR students only need D6, the principle of encryption.
What is in a packet header?
For Cambridge IGCSE 0478, the packet header holds the destination address, the packet number and the originator's address. The rest of the packet is the payload, which is the data itself, and the trailer, which marks the end of the packet.
What is the difference between serial and parallel transmission?
Serial transmission sends one bit at a time down a single wire, so it is reliable over long distances but slower. Parallel transmission sends several bits at the same time down several wires, so it is faster over short distances, but over long distances the bits can be skewed.
How does a parity check detect errors?
The sender and receiver agree on odd or even parity, and a parity bit is added to each byte to make the number of 1s odd or even. After transmission the receiver counts the 1s in each byte, and if the count does not match the agreed parity, an error is detected.
What is the difference between a check digit and a checksum?
A check digit checks data entry: it is calculated from the other digits of a number, such as an ISBN, and recalculated when the number is entered. A checksum checks data after transmission: the receiver recalculates it from the data received and compares it with the one sent.
Does encryption stop data being intercepted?
No. Encrypted data can still be intercepted, but it is scrambled, so it cannot be understood without the key. Only someone with the right key can decrypt it.
Previous module: Data representation revision notes.
More help: browse the GCSE Computer Science revision hub.